Monthly Archives: April 2019

Nice jig for crown molding

Posted on April 22, 2019 by robertwilkie

I like this jig, cause I typically try to do it by hand on the miter saw, this would make it a lot easier. One difference I would do, make 2 so there is on on each side. https://www.instructables.com/id/Jig-for-Cutting-Perfect-Crown-Molding/

Posted in Cheap, Misc-Life, Tools | Comments Off on Nice jig for crown molding

3D Router, hand based tool

Posted on April 21, 2019 by robertwilkie

The author basically made a 3D CNC, but, its all hand controlled. Not a bad idea to get presision slots and cuts without having to go to CAD, then CAM, then setup a CNC. Just alot of work to make. … Continue reading →

Posted in CNC/3D-printing, Tools | Comments Off on 3D Router, hand based tool

Making a lathe chuck

Posted on April 20, 2019 by robertwilkie

Nice build for a lathe chuck. Not so sure I would put all this effort into one myself. https://www.paoson.com/en/blog/lathe-longworth-faceplate–n65

Posted in Misc-Life, Tools, woodworking | Comments Off on Making a lathe chuck

Make your own sawhorses from plywood

Posted on April 20, 2019 by robertwilkie

Interesting build, looks like the author used 3/4 plywood, and nice faced stuff (not cheap stuff). Me….I think you can get 2 of the plastic sawhorses at Harbor Frieght for $15, not as nice looking but cheaper and quicker. http://www.homemadetools.net/forum/diy-plywood-sawhorses-72205?homelistings#post130540

Posted in Tools, woodworking | Comments Off on Make your own sawhorses from plywood

Interesting CNC build

Posted on April 19, 2019 by robertwilkie

could be a bit more complicated of a CNC to control, as you need to handle the table spinning. But it does save on number of motors and other parts a standard CNC would use. The write up is not … Continue reading →

Posted in Arduino, Cheap, CNC/3D-printing, Misc-Life | Comments Off on Interesting CNC build

Door holders

Posted on April 18, 2019 by robertwilkie

This is a nice build for door holders. Why would you need this? Well if you need to shave a door down to size to fit, these stands would be great to use. http://www.homemadetools.net/forum/spring-loaded-door-buck-door-stand-72030?homelistings#post129846

Posted in Misc-Life, Tools | Comments Off on Door holders

Make an oscillating sander with your drill press

Posted on April 17, 2019 by robertwilkie

I got a kick out of this one. The author builds the standard drum sander like build for the drill press, but then attaches a motor to the crank for the shaft for the drill press to have it go … Continue reading →

Posted in Cheap, Misc-Life, Tools | Comments Off on Make an oscillating sander with your drill press

This is a death sentence from your spouse if you do it

Posted on April 16, 2019 by robertwilkie

Clever idea, using the kitchen aid attachment for a disk sander. But…if I did this, yeah I will have to find a new home. https://www.instructables.com/id/KitchenAid-Benchtop-Disc-Sander/

Posted in Cheap, Tools | Comments Off on This is a death sentence from your spouse if you do it

Scary, but looks like it works wire stripper

Posted on April 15, 2019 by robertwilkie

I have toyed with wire stripping off and on for years. Once when copper went thru the roof I collected a bunch and made a pretty good penny off it. But stripping it was painful. This tool build looks like … Continue reading →

Posted in Cheap, Tools | Comments Off on Scary, but looks like it works wire stripper

Amazing lathe and drum sander build

Posted on April 14, 2019 by robertwilkie

This guy makes everything from wood…well most everything. The drum sander attaches to his homemade lathe. https://www.paoson.com/en/blog/lathe-sanding-station-thickness-sander-n72

Posted in Tools, woodworking | Comments Off on Amazing lathe and drum sander build